Installation Instructions

Remington 700 Staged-Break Trigger Installation Instructions

Normal Installation Time 15-30 minutes.

Tools required to replace trigger: hammer, (UNDERSIZE/LESS THAN) <1/8” punch (3mm, 3/32”).

If in doubt or questions - Please Call Huber Concepts at (920) 921-9641 or email us at HuberConceptsLLC@Gmail.Com. Or you can seek your favorite qualified gunsmith for assistance.

SAFETY FIRST!

  • Remove Source of Ammunition
  • Clear Chamber and Safety ON
  • Read & Understand these Instructions

1. Remove bolt from receiver & set aside. Note: Huber trigger has a current provision for “Bottom Bolt Release”. OR use Allen Wrench ( 1/16”) 1 st Stage length adjustment tool) to operate left top-side Bolt Release lever.

2. Remove Barreled Action from Stock/Chassis for access to trigger mount pins.

3. Using your Slave Pins (to secure old trigger intact when removed), and your Punch (UNDERSIZE 1/8”) (<.118”/3mm recommended), Drift trigger mount pins, Rear pin First, Right-to-Left, to position slave pins through trigger only and liberate receiver bolt release Lever & Spring. Drift front pin Left, align slave pin in trigger and remove old trigger from receiver (trigger) well.

Caution: Not to damage bolt stop, at front pin left side, by drifting front pin left after removing bolt release lever.

4. Place HUBER trigger in trigger well of receiver & sliding Safety handle along Receiver, align and re-pin Front mount pin-First. USE YOUR EYES TO ENSURE PROPER PIN ALIGNMENT. Clear pin-left end -of release lever slot in receiver. Slave pin will fall free. Re-install Rear pin from left, securing bolt release Lever &Spring, securing trigger and displacing slave pin. Top Bolt Release Lever will continue to function properly. If sear inadvertently released – with Allen wrench, tend sear spring into pocket from rear under sear. Re-install bolt and close action. Bolt Stop Release may be tweaked with needle nose pliers to accommodate various chassis designs.

FUNCTION CHECK:

  • Set Safety to SAFE, attempt to fire- Should NOT Fire. Safety blocks trigger prior to the 2 nd stage and lifts sear.
  • Set Safety to FIRE, attempt to fire- should FIRE thru 2-Stage function.
  • Trigger remains loaded thru shot & follow-thru and should return to base. Trigger CONNECTOR resets as bolt is opened and cycled or SAFETY to ON.

5. Re-Install Barreled Receiver into Stock/ Chassis.

6. FINAL FUNCTION CHECK.

DISCLAIMER: Trigger Form & Function is set at the factory. Geometry and adjustability’s are NON-Linear. Any tampering (USER Adjustment) will void warranty and potentially compromise performance and safety.

WARRANTY: Huber Concepts Triggers are warranted against defect in design, manufacturing and materials to the original purchaser for One (1) year. No warranty against misuse, abuse, deliberate tampering, unauthorized alterations and other circumstances beyond our control. Limits not to exceed cost of repair or replacement.

Not responsible for subsequent actions, injury or damage to persons or other equipment.

Return Policy for all issues, repairs or replacement at Huber Concepts determination and discretion. 

CARE & CLEANING

HUBER Triggers are designed to operate DRY or Lightly oiled. But, KG-5 lubrication is recommended for normal situations. As the trigger is an important component of the rifle and your discipline & proficiency, Care & Cleaning should follow along with your regular rifle maintenance routine. Triggers are not immune to weather & environment, neglect and abuse.

The current Huber trigger has provision for Remington Lower Bolt Release Lever actuated in front of the trigger.

Recommended Cleaning solvents and lubricants: KG-5, REM-OIL, BRAKLEEN, MEK, TCE, Alcohol, Napthalene lighter fluid, other high vapor pressure, rapid evaporating cleaning solvents. Avoid ammonia

Compressed Air/ Canned dry air (computer cleaning/dust remover products)

1. Trigger: IN or OUT of stock/chassis, mounted to receiver Intrusion gates, edges and all exposed areas.

2. Trigger: Out of stock/chassis, Not mounted to receiver Top access – liberate rear sear pin, allow sear to rotate up – on to front sear pin to inspect and clean internals or thru side window. To close sear using Allen wrench from rear, tend sear spring into sear spring pocket, re-pin and confirm full sear travel when trigger pulled fully to fire.

Triggers are shipped lightly lubricated with KG-5 for “break-in”. Subsequently, trigger can be run dry or lightly lubricated. Adverse conditions may necessitate more frequent inspection and cleaning. Lightly LUBRICATE with KG-5 (SHAKE WELL) Sear/ Connector contacts thru window Pivots (sear, safety, trigger, connector)

30-40 KRAG-JORGENSEN 1892-1898 SPRINGFIELD Install Instructions

  1. Make sure firearm is unloaded and in safe operating condition. Do NOT install this trigger if Safety, Sear or Cocking piece worn or damaged.
  2. Remove action Screws & barrel Bands, then Remove barreled Action from Stock.
  3. Swing Sear down to clear action Slot and compress spring. Sear & trigger come out to the left.
  4. Remove trigger PIN and replace with Huber trigger and re-pin to sear. Reinstall SEAR
  5. Remove wood in stock to clearance screw boss at front of trigger (figure 1). Typically use a ROTOZIP or DREMEL tool.
  6. With bolt closed, adjust creep screw (1) up to release point AND back off ¼-½ turn. For more creep – back off a little more. Minimum safe sear engagement is .015 in. or more! Ball adjustment is base set for clearance of trigger back.
  7. With bolt closed, adjust screws to fine tune for function or personal preference. Release point is where trigger will fire the gun.
  8. Reassemble barreled action to stock, screws & bbl bands.
  9. Cycle firearm for function and fine tune for desired feel.
  10. Enjoy shooting Mil-Surp rifles with your new HUBER CONCEPTS precision anti-friction ball trigger.

SAFE FIREARMS HANDLING RULES

  1. Treat every firearm as if it were loaded.
  2. Control the muzzle.
  3. Know your target and beyond.
  4. Keep finger away from trigger until ready to fire.

Husqvarna HVA Install Instructions

  1. Make sure firearm is unloaded and in safe operating condition. Do NOT install this trigger if Safety, Sear or Cocking piece worn or damaged.
  2. Remove barreled action and floorplate from stock assembly.
  3. Drift out trigger pin thru hole in SAFETYwith sear supported.
  4. OR Remove Safety screws & sear pin first to separate sear/trigger from action.
  5. Install Huber trigger and re-pin to sear.
  6. Re-pin sear w/ springs to action.
  7. Remove sufficient wood in stock to clearance control arms below sear. Typically use a ROTOZIP or DREMEL tool.
  8. With floorplate attached to action, adjust creep screw (1) to position trigger at front of floorplate slot.
  9. With bolt closed, adjust ball screw (2) up to release point AND back off ½ turn. For more creep or – back off a little more. Minimum safe sear engagement is .015in. or more! Screw settings MUST work within SAFETY limit slot to function properly with factory minimum sear engagement.
  10. With bolt closed, adjust over-travel screw (3) to find release point AND then back off ½ -1 full turn.
  11. Release point is where trigger will fire the gun.
  12. Reassemble barreled action and floorplate to stock. Cycle firearm for function and fine tune for desired feel.
  13. Enjoy shooting Mil-Surp rifles with your new HUBER CONCEPTS precision anti-friction ball trigger.

NOTE: Early Mausers, Arisaka & Enfield P-1914/17 rifles.

The small vertical rod at front of sear, adjacent to spring (concentric w/spring -Arisaka) is a Bolt-in-Battery Safety and engages 6 o’clock bolt notch.. When trigger set close to release point, rod interferes with bolt through charging cycle. This feature can be safely defeated by removing or grinding short. Feature not found on later models.

SAFE FIREARMS HANDLING RULES

  1. Treat every firearm as if it were loaded.
  2. Control the muzzle.
  3. Know your target and beyond.
  4. Keep finger away from trigger until ready to fire.